S Series — Slot Diffuser for Ceiling or Sidewall Applications

Extruded aluminum construction
Three slot types: 50 (1/2" slot), 75 (3/4" slot), 10 (1" slot)
One to eight slots wide for air volume of 10-350 cfm per foot
Adjustable pattern controller
Minimum one - Piece Length: 12"
Maximum one-piece length 72", lengths over 72' made in multiple units with pin splices for even continuous lengths (1/8" increments). 999" maximum continuous length.

Note: The width dimension is determined by the slot width (type) and the number of slots.

How to Specify

S [1] [2] [3] [4] [5] [6] [7]

[1] Type:

50 — 1/2" slot
75 — 3/4" slot
10 — 1" slot

[2] Style:

Diffuser Only
Diffuser with pattern controller

[3] Number of Slots:

1-8 slots
Note: Use a two-digit number to specify;
Example: for two slots, specify "02"

[4] Mounting Style:

B0 — T-Bar Lay-in - Diffuser Only
E0 — Diffuser Only
E1 — Hanger Bracket
E2 — Standard Mounting Frame
F0 — Screw Holes into Margin

[5] End Caps:

E1 — One end
E2 — Both ends
00 — None

[6] Length (inches)

12" Minimum
999" Maximum

[7] Finish

SA — Satin Anodized
W — White

How to Specify - Mitered Corners

S [1] [2] [3] [4] [5] [6] [7]

[1] Type:

50 — 1/2" Slot
75 — 3/4" Slot
10 — 1" Slot

[2] Number of Slots:

01-08 — Slots Available
Note: Use a two-digit number to specify;
Example: for two slots, specify "02"

[3] Mounting Style:

B0 — T-Bar Lay-in - Diffuser Only
E0 — Diffuser Only
E1 — Hanger Bracket
E2 — Standard Mounting Frame
F0 — Screw Holes into Margin

[4] Miter Type:

C — Ceiling
SI — Sidewall Inside
SO — Sidewall Outside

[5] MC

[6] 90

[7] Finish

SA — Satin Anodized
W — White

How to Purchase

FAQs for GRDs

Engineering Data — S Series

Style B0

B0 – T-Bar Lay-in - Diffuser Only

Duct Width: A + 1/16

Overall Width: A + 7/8

Please see Submittal Drawing for details

T-Bar Application

Order the length shown below:

	2'x2'	2'x4'
with End Caps	23 3/4"	47 3/4"

Submittal Data — B0

Style E1/E2

E1 – with Hanger Bracket

Overall Width: A + 3/4

Please see Submittal Drawing for details

E2 – Mounting Frame

Overall Width: A + 3/4

Please see Submittal Drawing for details

Style E0/F0

E0 – Diffuser Only

Duct Width: A + 7/16
Overall Width: A + 7/8

Please see Submittal Drawing for details

F0 - Screw Holes in Margin

Duct Width: A + 7/16

Overall Width: A + 7/8

Please see Submittal Drawing for details

Duct Width: A + 7/16

Overall Width: A + 7/8

Submittal Data — E0/F0

S Series Mitered Corners

Mitered Corners

90-degree mitered corners are available as factory-fabricated section. Precise factory cutting and assembly reduces field fabrication time and assures proper fit. Corner sections are furnished and blanked off. Corner sections butt to adjacent straight sections, which are spliced together with aligning keys.
Mitered corners are furnished in Mouting Style E2. When viewed from the room side, the mitered corner section appears identical to the butting straight sections.
Plaster frame mitered corners can be specified with the outlet mitered corner.

NOTE: DRAWING REQUIRED when ordering linear or slot diffusers with mitered corners.

Submittal Data — S Series Mitered Corners

First Name

Last Name

Phone Number

How can we help you?

Message

Mobile/SMS Opt In

By checking this box, I expressly consent to permit Hart & Cooley to send marketing or informational messages, including calls and texts made using an automated telephone dialing system to the number I provided above. I understand that consent is not required to obtain any good or service, and I can opt out of texts at any time by replying STOP to the number. Message and data rates may apply.

S Series — Slot Diffuser for Ceiling or Sidewall Applications

Engineering Data

Submittals

Options